3MTM
Safety-Walk Slip Resistant Tapes and Treads come
ready for installation. Make sure surface is clean, dry, smooth
and above minimum application temperature before beginning
the installation process. |
|
| |
| |
3MTM
Safety-WalkTM
Slip Resistant Tapes and Treads Installation Process
|
|
| |
 |
 |
 |
|
| |
Clean the area with soap
and water to remove any grease or dirt. Rinse thoroughly
and allow to dry. |
For porous surfaces
(like unpainted wood or concrete), apply 3MTM
Safety-WalkTM
Primer with a brush on the exact area where the 3MTM
Safety-WalkTM
Slip-resistant tape is to be placed. Allow primer to
dry. |
Peel one end of the Safety-Walk
product backing and place it in the appropriate area.
Try not to touch the adhesive. |
|
| |
 |
 |
 |
|
| Apply the remaining Safety-Walk product
by gradually pulling the liner and pressing in place. Use
a small rubber roller to help provide a firm bond. |
For 3MTM
Safety-WalkTM
Conformable Treads only, use a rubber mallet to conform
the Safety-Walk slip-resistant product to the irregular
surface. |
For wet areas, 3MTM
Safety-WalkTM
Edge Sealing Compound on the edge of the Safet-Walk slip
resistant product, making sure that the sealer bead cover
the edge of both the tread and the floor. After the edge
sealer dries (typically 30 minutes), the area is ready for
use. |
|
| |
| |
| Maintenance:
Inspect the application periodically
to maintain product effectiveness and insure serviceability. Regularly
scrub the treads with a stiff bristle brush to insure that they
are kept free from dirt and other residue that might impair
functionality. Wash with soap and water to keep material and surrounding
surfaces dirt- and grease-free. |
|
|
| Limited
Warrantee: Except where prohibited by law, the following is made
in lieu of all express or implied warrantees and conditions, statutory
or otherwise. 3M warrants that its
3MTM Safety-Walk Slip
Resistant Tapes and Treads will be free from defects
in material and manufacture at the time of purchase. There are
many factors that can effect the performance and useful life of
this product; i.e. the type and preparation of the surface, the
condition of use or exposure, etc. Due to the variety of
factors that can effect the use and performance of this product,
most of which are uniquely within the user's knowledge and control,
it is essential that user (a) determines whether or not this product
is fit for the desired purpose, (b) suitable for user's method
of application, (c) adequately maintained, and (d) is replaced
at end of useful life. |
| Limitation
of Remedies and Liability: 3M's only obligation shall be to repair
or replace, at 3M's option, such quantity of the material proved
to be defective. 3M shall not be liable for any injury, loss or
damage, direct, indirect, incidental, special or consequential
arising out of the use of this product, regardless of legal theory
asserted. This warranty gives specific legal rights. Others may
be available. |
| |
| |
| |
| |
| THE
MAT KING
1600
Old Country Road; Suite 207
Plainview, NY 11803 USA
Phone: 516-501-0744
Fax: 516-501-0753
Phone: 800-442-6544
Fax: 800-Mats-Fax (628-7329)
 |
| |
©
1996-2006
Jandru Mats, Inc. d/b/a The Mat King
All
Rights Reserved. Reproduction Prohibited.
It
is prohibited to use any graphics or images
in this web site
without the written permission of Jandru
Mats, Inc. |
Designed
& maintained by Geoffrey
Drew Marketing
Hosted by Geoffrey
Drew Marketing |
|
|
|
|
